Products -> Safety -> Omni Non-Wireless Accessories

This module adds 16 fully configurable input zones to a Lumina, Lumina Pro, Omni, Omni II, Omni IIe, OmniPro, or OmniPro II home control system system. The module comes with mounting hardware and cable to attach to the controller. Terminals are provided for 16 additional zones that can be programmed for burglary, fire, temperature or auxiliary inputs.

Up to 2 modules can be installed on the Lumina, Lumina Pro, Omni II, Omni IIe, and OmniPro II home control systems for an additional 32 zone inputs.

The Model 17A00-1 Expansion Enclosure adds sixteen voltage outputs for control and sixteen inputs for additional security/fire zones, auxiliary or temperature inputs.

The 17A00-1 can be mounted up to 1000 feet from the main controller and has its own power supply and battery. It reduces wiring use in larger installations.

It is commonly used for sprinkler systems, control of pumps, motors, remote control circuit breakers, and additional security/fire zones.

Up to four Expansion Enclosures can be used in conjunction with the HAI Lumina Pro, OmniPro, or OmniPro II home control system. Optional Model 19A00-1 8-Relay Module and Model 10A07-1 4-Relay Module mount in the enclosure.

It comes with a lock set with two keys.

The Model 17A00-9 is a 16 input/16 output expansion board on a universal mounting plate with accessory kit and instructions for installation in Leviton, UStec, OnQ/Legrand and "open house" type structured wiring enclosures

For use with a Lumina Pro or OmniPro II home control system.

The Model 17A00-8 Expansion Board is the board only portion of the Model 17A00-1 Expansion Enclosure.

It adds sixteen voltage outputs for control and sixteen inputs for additional security/fire zones, auxiliary or temperature inputs.

For use with an HAI Lumina Pro, OmniPro, or OmniPro II home control system.

This module expands the Omni LT by adding 16 zones and 8 voltage outputs with overload protection and reset. The module comes with mounting hardware and cable to attach to the Omni LT home control system.

The 16 zones can be programmed for burglary, temperature or auxiliary inputs. The 8 outputs have individual overload protection, with overload indicator and reset button.

The Model 36A10-1 HLC Expansion Kit contains a serial interface, cable, and PIM to add HLC to an Omni LT home control system that does not have a free serial port.

Relay Modules are used to convert HAI voltage outputs to Form C relay contacts for switching pumps, motors, commercial lighting, remote control breakers, and sprinkler systems. This Relay Module provides 4 independent Form C Relays. Contacts rated 5 amps at 24 VDC. LED indicators show which relays are energized. This model is supplied with foam adhesive mounting tape.

For the Lumina, Lumina Pro, Omni LT, Omni II, Omni IIe, or OmniPro II home control systems.

Relay Modules are used to convert HAI voltage outputs to Form C relay contacts for switching pumps, motors, commercial lighting, remote control breakers, and sprinkler systems. This Relay Module provides 8 independent Form C Relays. Contacts rated 5 amps at 24 VDC. LED indicators show which relays are energized. This model has mounting holes.

Mounts in Lumina Pro / OmniPro II 17A00-1 Expansion Enclosure.

RS-232/485 serial board, accessory kit, 20 pin cable, instructions.

For the Lumina, Lumina Pro, Omni LT, Omni II, Omni IIe, or OmniPro II home control systems.

EPROM chip upgrade with installation instructions as follows:

• OmniPro II Upgrade Chip
  (HAI Part Number 20A04-2UPG)
  
  
• OmniPro II (Spanish) Upgrade Chip
  (HAI Part Number 20A04-42UPG)
  
  
• Omni II Upgrade Chip
  (HAI Part Number 20A04-1UPG)
  
  
• Omni IIe Upgrade Chip
  (HAI Part Number 20A04-50UPG)
  
  
• Omni LT Upgrade Chip
  (HAI Part Number 21A03-1UPG)
  
  

Lock and two keys for an HAI enclosure.

This cable connects the built in serial port of a Lumina, Lumina Pro, Omni LT, Omni II, Omni IIe, or OmniPro II home control system to personal computers for HAI Web-Link II, HAI Windows PC Access, and other systems.

Cable is 7 feet long and has a DB-9F connector.

The 36A05-4 Serial Connectivity Adapter Kit is a Modular to DB-9M adapter and a 7-ft 4-conductor modular cable used to connect Lumina, Lumina Pro, Omni LT, Omni II, Omni IIe, and OmniPro II modular serial ports to DB-9F serial port on devices such as Lutron RadioRA, and Connectivity Partner Audio Systems from NuVo, Proficient Audio Systems, Russound, SpeakerCraft, and Xantech (Lumina Pro and OmniPro II only).

The UPB™ PIM to computer cable is used to connect the UPB™ PIM (HAI Part Number 36A00-1) to a computer's standard DB-9 serial port for use with HAI UPB™ UPStart configuration software.

The Model 10A11-1 Two-Way Audio/Voice Alarm Module allows two-way communication with a central station after an alarm, paging and listening from an on-premises or remote phone, annunciation of alarm and zone by voice, and voice messaging (not available on all systems). After an audible alarm, the module allows the central station to control the listen/talk mode. After a silent alarm, the module allows listen in only.

The Two-Way Voice Module provides a line-level audio output that can be tied into an amplifier or whole home audio system, such as Hi-Fi by HAI, and a page output that is activated whenever the Two-Way Voice Board generates audio output.

The Two-Way Voice Module will allow someone to broadcast messages through the phone by picking it up and dialing #832.

Do not mount speakers, microphones, 28A00 modules, or 33A00-4 consoles near any device that may produce noise (fans, air conditioning units, audio speakers, etc.). Microphones should be connected with 24 AWG or larger, shielded twisted pair wire. Wire length should not exceed 100 feet. Connect the cable shields and negative wires together at the Model 10A11-1, Rev B terminal block only. Do not connect the shield on the microphone end. Additional microphones can be connected to each input in parallel. Speakers should be connected with 18 AWG or larger, twisted pair wire. For wire runs that exceed 50 feet, use 16 AWG wire or larger. Wire length should not exceed 100 feet.

Use with HAI Part Number 33A00-4 Omni Console with Built-In Speaker/Microphone, 33A00-20 Lumina Keypad with Built-In Speaker/Microphone, 28A00-1 Surface Speaker Microphone, or 28A00-2 Flush Speaker Microphone.

The Model 10A11-1 may be used with Lumina, Lumina Pro, Omni LT, Omni, Omni II, Omni IIe, OmniPro and OmniPro II home control systems.

The Model 28A00-1 is a speaker and microphone assembly that allows two-way communication with a central station after an alarm, paging and listening from an on-premises or remote phone, annunciation of alarm and zone by voice, and voice messaging (not available on all systems) when connected to a Two-Way Voice Module. It may be used outdoors in weather protected areas.

Do not mount speakers, microphones, 28A00 modules, or 33A00-4 consoles near any device that may produce noise (fans, air conditioning units, audio speakers, etc.). Microphones should be connected with 24 AWG or larger, shielded twisted pair wire. Wire length should not exceed 100 feet. Connect the cable shields and negative wires together at the Model 10A11-1, Rev B terminal block only. Do not connect the shield on the microphone end. Additional microphones can be connected to each input in parallel. Speakers should be connected with 18 AWG or larger, twisted pair wire. For wire runs that exceed 50 feet, use 16 AWG wire or larger. Wire length should not exceed 100 feet.

Dimensions: 5 3/16" H x 5 3/16" W x 2 5/8 D

Requires Two-Way Voice Module (HAI Part Number 10A11-1).

Works with Lumina, Lumina Pro, Omni LT, Omni II, Omni IIe, or OmniPro II home control systems.

The Model 28A00-2 is a speaker and microphone assembly that allows two-way communication with a central station after an alarm, paging and listening from an on-premises or remote phone, annunciation of alarm and zone by voice, and voice messaging (not available on all systems) when connected to a Two-Way Voice Module. It may be used outdoors in weather protected areas.

Do not mount speakers, microphones, 28A00 modules, or 33A00-4 consoles near any device that may produce noise (fans, air conditioning units, audio speakers, etc.). Microphones should be connected with 24 AWG or larger, shielded twisted pair wire. Wire length should not exceed 100 feet. Connect the cable shields and negative wires together at the Model 10A11-1, Rev B terminal block only. Do not connect the shield on the microphone end. Additional microphones can be connected to each input in parallel. Speakers should be connected with 18 AWG or larger, twisted pair wire. For wire runs that exceed 50 feet, use 16 AWG wire or larger. Wire length should not exceed 100 feet.

Dimensions: 4 1/2" H x 4 1/2" W x 1 1/2" D (Protrudes only 1/2" when flush mounted)

Requires Two-Way Voice Module (HAI Part Number 10A11-1).

Works with Lumina, Lumina Pro, Omni LT, Omni II, Omni IIe, or OmniPro II home control systems.

PLEASE CHECK WITH HAI FOR AVAILABILITY

The Two-Way Cellular Communication Center (CCC) connects with any burglar or fire alarm panel, including HAI controllers, to emulate the phone line signal if there is not one present.

The Two-Way CCC dials out using a cellular network to communicate with a central monitoring station in any format for any panel. It also allows telephone calls to be made or received over the Cellular network using a land line telephone in the home. The central station can call the homeowner for verification in the event of an alarm.

It is an excellent option for security and/or automation installations where there is no land line or as added protection if the main phone is cut.

The Two-Way CCC ships with an included backup battery and antenna. It requires a GSM SIM card and cellular service.

Mounting plate, hardware kit & instructions. Used to mount Omni family controllers, expanders, and accessories in Leviton, OnQ/Legrand, UStec, and "open house" type structured wiring enclosure

For use with a Lumina, Lumina Pro, Omni II, Omni IIe, or OmniPro II home control system.

Mounting plate hardware kit & instructions. Used to mount Omni LT controllers in Leviton and "open house" type structured wiring enclosures.

For use with an Omni LT home control system.

Fully assembled & operational OmniPro II demo system including controller, RC-80B Omnistat thermostat, LCD console with built-in speaker, OmniTouch 5.7 Touchscreen, HAI Lighting Control: House Status Switch, Scene Switch, and Dimmer, UPB™ PIM, Voice Module, packaged in super duty black travel case. Demo programs included.

The Model 18A00-5 Demo Board Adapter Kit is a pre-wired circuit board that plugs into the terminal sockets on a Lumina, Lumina Pro, Omni II, Omni IIe, or OmniPro II home control system. It is used in HAI Demo Systems and now may be used by dealers or builders for showroom displays, model homes, and other product demonstration applications.

Features include quick connect to console, thermostat, telephone, PC and 24 VAC transformer plus phone line simulator, modular jacks for phone and console connections, built in temperature sensor simulator, and two switched zones for security demonstration.

The Model 27A00-2 Demo Board Adapter Kit is a pre-wired circuit board that plugs into the terminal sockets on an Omni LT home control system. It is used in the HAI Omni LT Demo System and now may be used by dealers or builders for showroom displays, model homes, and other product demonstration applications.